Welcome to Dongguan Changchong Plastics Co.,Ltd

Service Hotline:

0769-87131326

搜索
Search

Hot Search: Plastic raw materials | Plastics | Engineering plastics | Changchun plastics | Special engineering plastics

News Center

Check category
Service Hotline:86-769-87131326

Professional custom production, integrity to achieve win-win situation

Mobile: 86-15989877778
Fax: 86-769-87131336
E-mail: htpa46@aliyun.com
ADD:China's Dongguan City, Guangdong Huangjiang Fukang Commercial Building, Room 905 (Office: Ningbo Yinzhou / Kunshan, Jiangsu)
Web: http://www.ccppbt.com

/
/
/
What are the process conditions for PBT injection molding?

What are the process conditions for PBT injection molding?
Top

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2021-07-13 09:14
  • Views:

(Summary description)

What are the process conditions for PBT injection molding?
Top

(Summary description)

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2021-07-13 09:14
  • Views:
Information

Forming performance of PBT

 

1) PBT has low hygroscopicity, but it is more sensitive to moisture at high temperatures. It will degrade the PBT molecules during the molding process, darken the color and produce spots on the surface, so it should usually be dried.

 

2) PBT melt has excellent fluidity, so it is easy to form thin-walled and complex-shaped products, but pay attention to mold flashing and nozzle drooling.

 

3) PBT has an obvious melting point. When the temperature rises above the melting point, the fluidity will increase suddenly, so attention should be paid to it.

 

4) PBT has a narrow molding processing range, crystallizes quickly when cooling, and good fluidity, which is especially suitable for rapid injection.

 

5) PBT has a larger shrinkage rate and shrinkage range, and the shrinkage rate difference in different directions is more obvious than other plastics.

 

6) PBT is very sensitive to the response of notches and sharp corners. Stress concentration is likely to occur at these positions, which greatly reduces the load-bearing capacity and is prone to rupture when subjected to force or impact. Therefore, this point should be paid attention to when designing plastic parts. All corners, especially the internal corners, should use arc transitions as much as possible.

 

7) The elongation rate of pure PBT can reach 200%, so products with smaller depressions can be forced out of the mold. However, after filling with glass fiber or filler, its elongation is greatly reduced, and if there are depressions in the product, forced demoulding cannot be implemented.

 

8) The runner of the PBT mold should be short and thick when possible, and the round runner will have the best effect. In general, both modified and unmodified PBT can be used with ordinary runners, but glass fiber reinforced PBT can only have good results when hot runner molding is used.

 

9) The point gate and the latent gate have a large shearing effect, which can reduce the apparent viscosity of the PBT melt, which is conducive to molding. It is a frequently used gate. The gate diameter should be larger.

 

10) The gate is best to face the core cavity or core, so as to avoid spraying and minimize the filling of the melt when flowing in the cavity. Otherwise, the product is prone to surface defects and deteriorates performance.

 

The main injection molding conditions of PBT

 

1) The temperature of the barrel. The selection of barrel temperature is very important for PBT molding. If the temperature is too low, poor plasticization will cause the product to lack material, dent, uneven shrinkage and dullness. If the temperature is too high, it will cause serious salivation of the nozzle, overflow, darken the color and even degrade. Generally, the barrel temperature is controlled at 240~280℃, and the glass fiber reinforced PBT is controlled at 230~260℃. The temperature of the nozzle should be controlled at 5~10℃ lower than the temperature of the front part of the barrel.

 

2) Mold temperature. The mold temperature is directly related to the dimensional stability, warpage deformation, molding cycle and crystallinity of the product. PBT is easy to crystallize, and it crystallizes quickly even at room temperature, so the mold temperature does not need to be too high, usually 40~60℃, while the mold temperature of glass fiber reinforced PBT is slightly higher, usually 60~80℃.

 

3) Injection pressure. PBT has low melt viscosity and good fluidity. It can use medium injection pressure, generally 60~90MPa, and glass fiber reinforced PBT is 80~100MPa. Usually the injection pressure increases with the increase of the thickness of the plastic part, but should not exceed 100MPa , Otherwise it will make demoulding difficult.

Keyword:

Scan the QR code to read on your phone

Copyright © 2020  Dongguan Changchong Plastics Co.,Ltd  All rights reserved    粤ICP备19141054号       Powered by: 300.cn